The Gila was a wooden-hulled stern-wheel steamboat (sternwheeler) of the Colorado Steam Navigation Company that operated on the lower Colorado River from 1873 to 1899. It was one of the most durable and successful vessels in the river’s steamboat era, known for its shallow draft that allowed it to navigate the river’s shifting sandbars, low water, and difficult stretches while carrying freight, passengers, mining equipment, and supplies.
Description and Specifications
The Gila measured approximately 149 feet in length with a 31-foot beam and a hull depth of about 3.5–3.8 feet. It displaced 236 tons and drew only about 16.5 inches of water when light (unloaded), making it exceptionally well-suited to the Colorado’s shallow, variable conditions. Cargo capacity was typically around 125 tons, and it frequently towed barges that significantly increased overall payload.
It was a classic Western river sternwheeler: a flat-bottomed or lightly built wooden hull powered by a stern paddlewheel, optimized for maneuvering in confined channels and over bars rather than for open-water speed or deep draft. Passenger accommodations included staterooms (limited in number) and a dining area, though conditions were often harsh due to extreme desert heat. Contemporary accounts, such as Martha Summerhayes’s description of an 1874 voyage under Captain Jack Mellon, note the intense heat that made staterooms nearly unusable during the day, forced passengers to sleep on deck at night with straw bedding, and left even metal utensils uncomfortably warm. Meals were basic (biscuits, salted beef, canned vegetables), and drinking water was cooled only marginally by hanging flannel-covered canteens in the shade.
The boat was built in San Francisco by shipbuilder Patrick Henry Tiernan, shipped “knocked down” (disassembled) to Port Isabel, Sonora (near the Colorado River’s mouth on the Gulf of California), and reassembled and launched there in January 1873 under the supervision of veteran Captain David C. Robinson. It was constructed specifically as a replacement for the aging Nina Tilden, an earlier vessel acquired by George Alonzo Johnson’s interests after the failure of a rival company.
Historical Context of Colorado River Steamboating
Steamboat navigation on the Colorado began in the early 1850s primarily to supply the isolated U.S. Army post at Fort Yuma (near the Gila River confluence). Overland freight from California was extremely expensive (often hundreds of dollars per ton). Early side-wheelers such as the Uncle Sam (1852) and General Jesup demonstrated the feasibility of river transport; later sternwheelers with shallower drafts proved far more practical. The Colorado Steam Navigation Company (and its predecessors under George A. Johnson) dominated the trade, establishing woodyards along the river (often worked by Cocopah laborers) so boats could refuel overnight rather than gather wood en route. Boats did not run at night because of the constant hazards of shifting sandbars and snags.
By the 1860s–1870s the route extended from the delta (Port Isabel and earlier landings) past Yuma/Arizona City upriver to points such as Ehrenberg, Hardyville, Fort Mohave, and eventually farther north during high water or special voyages. Freight included mining machinery, coal, supplies, and merchandise inbound, and ore, wool, hides, and other products outbound. Passenger fares varied by distance.
Service History of the Gila
Launched in early 1873, the Gila quickly became a workhorse of the fleet. It hauled freight and passengers on the main lower-river routes for more than 25 years and was frequently commanded by skilled pilots, notably Captain John “Jack” Alexander Mellon (sometimes spelled Melon or Mellon). Mellon had extensive experience on the river and was known for innovative techniques such as using the sternwheel to dig through sandbars when necessary.
A notable chapter began in 1879 after the Southern Pacific Railroad interests acquired control of the steamboat company. The Gila was chartered to Joseph Wharton, who had consolidated mining operations in Eldorado Canyon (Nevada). Under Mellon’s command it delivered machinery to the canyon and then, in a pioneering voyage in July 1879, successfully navigated the previously uncharted Boulder Canyon to reach the mouth of the Virgin River at Rioville (Utah/Nevada border area). This proved that the Virgin River confluence was the practical head of steam navigation on the Colorado—something earlier explorers and operators (including Johnson, Ives, and Trueworthy) had believed possible but had not fully achieved. Over the next eight years the Gila made about 22 trips up to Rioville to obtain salt needed for processing silver ore at the Eldorado Canyon mills.
Throughout its career the boat supported the region’s mining booms, military posts, and settlements. It operated in an era when steamboats were the most economical way to move heavy goods into the arid Southwest until railroads progressively undercut the trade (Southern Pacific reached Yuma in 1877, and later lines further reduced river traffic).
Ports of Call and Route
Operations typically began at the Colorado River Delta/Gulf of California area (transferring cargo from ocean vessels to avoid Mexican duties or navigate shallow tidal waters) and ran upstream through Sonora, Baja California Territory, California, Arizona Territory, and into Nevada. Key landings and ports associated with the Gila and the broader fleet included:
- Port Isabel / estuary area (Sonora, Mexico): Assembly/launch site and southern terminal; early ocean-to-river transfer point.
- Yuma (Arizona City / Fort Yuma area): Primary hub, shipyard/repair site after the 1870s, and major transfer point. The Gila is documented there frequently (including with barges).
- Castle Dome Landing: About 35 miles above Yuma; served the Castle Dome mining district (lead ore, smelting).
- Ehrenberg (earlier Mineral City) and nearby La Paz / Olive City: Major mid-river ports roughly 125–130 miles above Yuma; key for central Arizona freight and passengers connecting to stage/wagon roads inland. Regular stops for the Gila and sister boats.
- Aubrey, Parker’s Landing, and intermediate woodyards/ranches: Wood fuel stops and minor landings.
- Fort Mohave / Hardyville (later near Bullhead City area): Important northern low-water head of navigation (~310 miles above Yuma); ferry and freight transfer for northern Arizona and mines. The Gila made regular runs here.
- Polhamus Landing (near Hardyville, established ~1881): Busy freight point in the early 1880s for mines and agencies.
- Eldorado Canyon area (Nevada): Mining support, machinery delivery, and ore/bullion transport.
- Callville: Mormon-founded landing; intermediate stop on upper runs.
- Rioville (also associated with Bonelli’s Ferry; at the Virgin River confluence, now under Lake Mead): High-water head of navigation (~440 miles from Yuma/Fort Yuma area). The Gila reached it repeatedly 1879–1887 for salt cargoes.
Other occasional or fleet-associated stops included various woodyards, Drift Desert, California Camp, and points serving Indian agencies or temporary mining camps. Upstream travel was slower and more hazardous (days to a week or more depending on water levels and destination); downstream was faster with the current. High water (spring snowmelt) enabled farther upstream travel; low water restricted boats to shallower-draft operations and lower landings.
The Gila exemplified the ingenuity required to make commercial steamboating viable on one of the West’s most challenging rivers. Its long service life and role in extending navigation to the Virgin River marked it as a standout vessel in the Colorado River steamboat era.
Fate and Legacy
After roughly 25–35 years of continuous hard service (sources vary slightly on the exact phrasing of longevity), the worn Gila was rebuilt in 1899 at Yuma. Its machinery was refurbished and installed in a new or heavily reconstructed hull launched as the Cochan (sometimes given as 135 feet long with similar beam and a still-shallow draft). The Cochan continued working the river into the early 1900s, including support for Imperial Valley projects, until commercial steam navigation effectively ended with the completion of Laguna Dam (about 14 miles above Yuma) in 1909, which blocked the channel. Residual river traffic continued on a limited basis for a few more years.
The Gila is remembered as one of the most durable and capable boats on the Colorado—outlasting many contemporaries and playing a key role in extending reliable navigation northward and supporting the mining and settlement economy of the lower Colorado River corridor during its peak steamboat decades. Photographs from the period show it tied up at Yuma and other landings, often alongside barges that served as floating docks or additional cargo capacity.